Home About APEM Events News Sponsorship
Advances in Production Engineering & Management

Archives > Volume 10 | Year 2015

Advances in Production Engineering & Management
Volume 10 | Number 4 | December 2015 | pp 165–230

Contents
Lean capacity planning for tool room: An iterative system improvement approach
Haider, A.; Mirza, J.; Ahmad, W.
http://dx.doi.org/10.14743/apem2015.4.200
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


The application of service robots for logistics in manufacturing processes
Karabegović, I.; Karabegović, E.; Mahmić, M.; Husak, E.
http://dx.doi.org/10.14743/apem2015.4.201
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


A grey-fuzzy approach for optimizing machining parameters and the approach angle in turning AISI 1045 steel
Senthilkumar, N.; Sudha, J.; Muthukumar, V.
http://dx.doi.org/10.14743/apem2015.4.202
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Permanent magnets for water-scale prevention
Lipus, L.C.; Hamler, A.; Ban, I.; Acko, B.
http://dx.doi.org/10.14743/apem2015.4.203
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Using entropy weight, OEC and fuzzy logic for optimizing the parameters during EDM of Al-24 % SiCP MMC
Bhuyan, R.K.; Routara, B.C.; Parida, A.K.
http://dx.doi.org/10.14743/apem2015.4.204
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)



Advances in Production Engineering & Management
Volume 10 | Number 3 | September 2015 | pp 111–164

Contents
Characterizations of 304 stainless steel laser cladded with titanium carbide particles
Mahmoud, E.R.I.
http://dx.doi.org/10.14743/apem2015.3.196
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


An integrated sustainable manufacturing strategy framework using fuzzy analytic network process
Ocampo, L.A.; Clark, E.E.; Tanudtanud, K.V.G.; Ocampo, C.O.V.; Impas Sr., C.G.; Vergara, V.G.; Pastoril, J.; Tordillo, J.A.S.
http://dx.doi.org/10.14743/apem2015.3.197
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Effect of a milling cutter diameter on distortion due to the machining of thin wall thin floor components
Sridhar, G.; Ramesh Babu, P.
http://dx.doi.org/10.14743/apem2015.3.198
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Experimental and simulation study on the warm deep drawing of AZ31 alloy
Reddy, A.C.S.; Rajesham, S.; Reddy, P.R.
http://dx.doi.org/10.14743/apem2015.3.199
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)



Advances in Production Engineering & Management
Volume 10 | Number 2 | June 2015 | pp 55–110

Contents
Modeling and optimization of parameters for minimizing surface roughness and tool wear in turning Al/SiCp MMC, using conventional and soft computing techniques
Tamang, S.K.; Chandrasekaran, M.
http://dx.doi.org/10.14743/apem2015.2.192
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Predictive analysis of criterial yield during travelling wire electrochemical discharge machining of Hylam based composites
Mitra, N.S.; Doloi, B.; Bhattacharyya, B.
http://dx.doi.org/10.14743/apem2015.2.193
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Increasing student motivation and knowledge in mechanical engineering by using action cameras and video productions
McCaslin, S.E.; Young, M.
http://dx.doi.org /10.14743/apem2015.2.194
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Wear characteristics of heat-treated Hadfield austenitic manganese steel for engineering application
Agunsoye, J.O.; Talabi, S.I.; Bello, O.
http://dx.doi.org/10.14743/apem2015.2.195
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)



Advances in Production Engineering & Management
Volume 10 | Number 1 | March 2015 | pp 1–54

Contents
An implementation of lean scheduling in a job shop environment
Haider, A.; Mirza, J.
http://dx.doi.org/10.14743/apem2015.1.188
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


Tool selection for rough and finish CNC milling operations based on tool-path generation and machining optimisation
Mwinuka, T.E.; Mgwatu, M.I.
http://dx.doi.org/10.14743/apem2015.1.189
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


The impact of technical and organisational innovation concepts on product characteristics
Koren, R.; Palčič, I.
http://dx.doi.org /10.14743/apem2015.1.190
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)


A hierarchical framework for index computation in sustainable manufacturing
Ocampo, Lanndon A.
http://dx.doi.org/10.14743/apem2015.1.191
ABSTRACT (HTML)  |  ABSTRACT AND REFERENCES (PDF)  |  FULL ARTICLE TEXT (PDF)

< PREVIOUS VOLUME   |   NEXT VOLUME >